hteinkmin.com

Bad sector has long been a scourge which is troubling for a number of computer users. Quite a lot of the factors that could cause Bad sector, but not as a means that can be done to restore the affected hard disk. Some time ago I read an article on a home computer tabloid, and the following tips can I rangkumkan for you. First you need a little know if Bad Sector Bad Sector and how it could happen. Hard Disk Bad sector can be affected by two possibilities, the first in a logical, and the second in physics. For the latter possibility, it will not be discussed too deep due to Bad Sector Physics be caused by physical damage to your hard drive.

Meanwhile, Bad Sector Logic can occur due to disruption of the operation of reading – writing in a sector. This may be caused by several possibilities, such as viruses, boot record of corruption, voltage disturbances and the possibility of peers.  When Bad sector in Logic occur on your hard disk, it is advisable to first try the software fixes your hard disk that is included when you buy a hard disk.

The software does not repair the broken sector, but hide it. In other words there is permanent damage, but the operating system to ignore. About the image of how it works is like this. The software restore hard disk magnetic orientation to make each byte read and write can do to allow the recovery of hard disk. Bad sectors can be spread on the hard drive, especially on one track of disk 0. Something like this can also you can not install and copy the data on your hard drive.

• Use your software to repair hard drive

Previously, there may be a simple way that can be done as first aid while the hard disk has bad sectors threatened. In Windows XP open the MS-DOS prompt is. Then type “chkdsk / r” and press Enter. This command will immediately find the position of Bad Sector and perform a rescue operation on the data can still be readable. For the series of Windows 95, 98 or Millennium, the Scandisk application that is built from the Windows application that can be tried. However, if still not satisfied and problems on the hard drive has not been resolved, there are other ways more below the maximum.

Basically, the hard drive has been equipped with software enhancements that happens when Bad sector on the hard drive. This software can manage a Bad Sector Logic. Here are some examples of software built from a number of hard drives. Maxtor and Quantum understands MaxBlast with ClearHDD Samsung Seagate Seagate equipped Formats, whereas Western Digital Old DLG Diagnostic achieved, and with Fujitsu FJ-IDE Drive Initializer utility.

But we must also not rule that maximizes the healing process of the hard disk Bad Sector use other software that is also very powerful. And this time, the software will try SpinRite is a software repair hard drive made by Gibson Research, the latest version is version 6.0. SpinRite supports FAT, NTFS, Linux, Novell, drives with multiple operating systems, and the hard disk is not formatted well. Here’s a little how to use it.

• Create a bootable CD or floppy disk. The manufacturing process can be performed directly in the SpinRite. Select “Startup Disk from Crete”, then “Create an ISO or image file, or it may be thanks to the option” Install the drive SpinRite. “To make it easier to apply just use a CD bootable. For the record, the next step will be much more time in DOS mode.
• After the image file created from SpinRite had already finished, then burn it onto a blank CD or a similar device using Nero CD burning. Restart the computer and boot with the CD that you just created.
• After successfully booting from the CD before, we will be in the SpinRite interface provides five options or may be called as the level of improvement. Please select an option when you need to repair the hard drive depending on the level of damage. Usually in most cases, the option number two and four of the most often required. second option is to restore the data, and option number four is the maintenance and analysis on the hard disk.
• After selecting the option that is required, you are asked to specify the drive or partition to be checked or repaired. Follow the next step is the consideration and determination of the option SpinRite will set to work doing his job on your hard drive.

The processing time is relatively based on the speed and capacity of your hard drive. SpinRite is able to repair your hard drive with 120 GB per hour maximum speed it. Although the speed of SpinRite is still heavily influenced by many factors, such as system configuration, damaged hard disk, or support of the Ultra DMA. But do not worry if you do not want to wait a long time and do not want to leave the repair process, SpinRite offers the convenience of the termination process of continuous improvement in the future. Just position inspection record live during shutdown process.

SpinRite will automatically dial the four-option, if after having verified the existence of repairs and maintenance on your hard drive. And this process also takes a bit, get to a matter of days even, depending on the level of damage to the hard drive itself. But it is surely better that you lose data, or to buy a new hard disk because the hard drive Bad sector who persecute you.

SpinRite also comes with a screen saver is active when the process is running. Can also display the current process. If your hard drive supports temperature readings, SpinRite will also display the temperature information on your hard drive. There are also other interesting features of “Data Recovery Dynastat” to display more closely the course of a process of continuous improvement.

Leave a Reply